Yamaha STAR XV19CSX Скачать руководство пользователя

Страница: 18 / 96

INSTRUMENT AND CONTROL FUNCTIONS

3-1

EAU10450

Main switch

The main switch controls the ignition
and lighting systems. The various main
switch positions are described below.

EAU10540

All electrical circuits are supplied with
power, and the meter lighting, taillight,
license plate light and position lights
come on, and the engine can be start-
ed. The key cannot be removed.

NOTE:

The headlight comes on automatically
when the engine is started and stays on
until the key is turned to “OFF”, even if
the engine stalls.

EAU10660

OFF

All electrical systems are off. The key
can be removed.

EAU11003

Indicator and warning lights

EAU11030

Turn signal indicator lights “

” and

“

”

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

1. Left turn signal indicator light “

”

2. High beam indicator light “

”

3. Neutral indicator light “

”

4. Right turn signal indicator light “

”

5. Engine trouble warning light “

”

6. Fuel level warning light “

”

U29S10E0.book Page 1 Friday, May 18, 2007 1:53 PM

Содержание STAR XV19CSX

































































































Результаты поиска

Содержание STAR XV19CSX

Отзывы:

Похожие инструкции для STAR XV19CSX

Бренды по названию

Популярные бренды

Yamaha STAR XV19CSX, Руководство пользователя

Результаты поиска

Содержание STAR XV19CSX

Отзывы:

Похожие инструкции для STAR XV19CSX

Бренды по названию

Популярные бренды