manualshive.com logo in svg

Yamaha Star 2010, Руководство пользователя

Поделиться
Скачать
Yamaha Star 2010 Скачать руководство пользователя страница 76

PERIODIC MAINTENANCE AND ADJUSTMENT

7-33

7

EAU42462

Replacing a front turn signal 
light bulb 

1. Remove the front turn signal light

outer lens by removing the screws.

2. Remove the inner lens by pulling it

out.

3. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

4. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

5. Place the inner lens in the original

position, and then install the outer
lens by installing the screws.

NOTICE:

 Do not overtighten the

screws, otherwise the lens may
break.

 [ECA10681]

EAU42452

Replacing a rear turn signal 
light bulb 

1. Remove the turn signal lens by re-

moving the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws. 

NOTICE:

 Do not over-

tighten the screws, otherwise
the lens may break.

 [ECA10681]

1. Screw

1. Inner lens

1. Screw

U5S614E0.book  Page 33  Friday, July 9, 2010  9:18 AM

Содержание Star 2010









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды