Yamaha Star 2010 Скачать руководство пользователя | Manualshive

Страница: 54 / 104

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-11

7

TIP

If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.

3. Install the spark plug cap.
4. Install the spark plug cover by in-

stalling the bolts.

EAU19681

Canister (for California only)

This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the fol-
lowing:

●

Check each hose connection.

●

Check each hose and canister for
cracks or damage. Replace if dam-
aged.

●

Make sure that the canister breath-
er is not blocked, and if necessary,
clean it.

EAU42599

Engine oil and oil filter car-
tridge

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.

To check the engine oil level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Wait a few minutes until the oil set-

tles, and then check the oil level
through the engine oil level check
window located at the bottom-left
side of the crankcase.

TIP

The engine oil should be between the
minimum and maximum level marks.

U5S614E0.book Page 11 Friday, July 9, 2010 9:18 AM

«
...
52
53
54
55
56
...
»

Содержание Star 2010









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star 2010

Бренд: N-Com Страницы: 6

Бренд: KEEWAY Страницы: 15

Бренд: R&G Страницы: 4

Бренд: Dakota Digital Страницы: 2

Бренд: SHOEI Страницы: 38

Бренд: KTM Страницы: 22

Бренд: Ohlins Страницы: 2

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 124

ROAD STAR XV16A

Бренд: Yamaha Страницы: 117

X MAX CZD300P 2022

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 97

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 96

Бренд: Dynafit Страницы: 20

Бренд: hepco & becker Страницы: 4

Бренд: Dakota Digital Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды