Yamaha Star 2010 Скачать руководство пользователя

Страница: 30 / 104

INSTRUMENT AND CONTROL FUNCTIONS

4-12

EAU48760

Fuel tank breather/overflow
hose

TIP

For California: See page 7-11 for
breather hose information.

Before operating the motorcycle:

●

Check the fuel tank breather/over-
flow hose connection.

●

Check the fuel tank breather/over-
flow hose for cracks or damage,
and replace it if damaged.

●

Make sure that the end of the fuel
tank breather/overflow hose is not
blocked, and clean it if necessary.

EAU13433

Catalytic converter

This model is equipped with a catalytic
converter in the exhaust system.

WARNING

EWA10862

The exhaust system is hot after op-
eration. To prevent a fire hazard or
burns:

●

Do not park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.

●

Park the vehicle in a place
where pedestrians or children
are not likely to touch the hot
exhaust system.

●

Make sure that the exhaust sys-
tem has cooled down before do-
ing any maintenance work.

●

Do not allow the engine to idle
more than a few minutes. Long
idling can cause a build-up of
heat.

NOTICE

ECA10701

Use only unleaded gasoline. The use
of leaded gasoline will cause unre-
pairable damage to the catalytic
converter.

1. Fuel tank overflow hose

2. Fuel tank breather hose

U5S614E0.book Page 12 Friday, July 9, 2010 9:18 AM

Содержание Star 2010









































































































Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды

Yamaha Star 2010, Руководство пользователя

Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды