46
SET MENU
Surround left/right speakers
1C SURR
Choices: LRG (large),
SML
(small), NON (none)
• Select “LRG” if you have large surround left and right
speakers. The entire range of the surround channel
signals is directed to the surround left and right
speakers.
• Select “SML” if you have small surround left and right
speakers. The low-frequency signals of the surround
channel are directed to the speakers selected with “1D
BASS”.
• Select “NON” if you do not have surround speakers.
This will set this unit to the Virtual CINEMA DSP
mode (see page 33).
Bass out
1D BASS
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
Choices: SWFR (subwoofer), FRNT (front),
BOTH
• Select “SWFR” if you connected a subwoofer. The
LFE signals as well as the low-frequency signals of
other speakers set to “SML” or to “NON” are directed
to the subwoofer.
• Select “FRNT” if you did not connect a subwoofer.
The LFE signals, the low-frequency signals of the front
left and right channels, and the low-frequency signals
of other speakers set to “SML” or to “NON” are all
directed to the front left and right speakers regardless
of the “1B FRONT” setting.
• Select “BOTH” if you connected a subwoofer. The
low-frequency signals of any source are output from
the subwoofer. The LFE signals as well as the low-
frequency signals of other speakers set to “SML” or to
“NON” are directed to the subwoofer. The low-
frequency signals of the front left and right channels
are directed to the front left and right speakers and the
subwoofer regardless of the “1B FRONT” setting.
■
Speaker distance
2 SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
Unit
UNIT
Choices: meters, feet
Initial setting:
[U.S.A. and Canada models]: feet
[Other models]: meters
• Select “meters” to adjust speaker distances in meters.
• Select “feet” to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial settings: 3.00 m (10.0 ft)
• Select “FRONT” to adjust the distance of the front
speaker.
• Select “CENTER” to adjust the distance of the center
speaker.
• Select “SURR” to adjust the distance of the surround
speaker.
• “CENTER” and “SURR” cannot be adjusted if “1A CENTER”
and “1C SURR” are set to “NON” respectively.
• No delay will be set if you set the same distance for “FRONT”,
“CENTER”, and “SURR”.
■
Low-frequency effect level
3 LFE LEVEL
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: –20 to
0
dB
Control step: 1 dB
Speaker
SP LFE
Adjusts the speaker LFE level.
Headphone
HP LFE
Adjusts the headphone LFE level.
• Adjust the LFE level according to the capacity of your
subwoofer or headphones.
• Depending on the settings of “1D BASS”, some signals may not
be output at the SUBWOOFER OUTPUT jack.
Notes
Notes
