Yamaha Raptor YFM35RA страница 119 Скачать руководство пользователя | Manualshive

Страница: 119 / 142

background image

9-1

9

EBU25860

CLEANING AND STORAGE

EBU25902

Cleaning

Frequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.

1. Before cleaning the ATV:

a. Block off the end of the exhaust pipe to

prevent water entry. A plastic bag and
strong rubber band may be used.

b. Make sure the spark plug and all filler caps

are properly installed.

2. If the engine case is excessively greasy, apply

degreaser with a paint brush. Do not apply de-
greaser to the chain, sprockets or wheel ax-
les.

3. Rinse the dirt and degreaser off with a garden

hose. Use only enough pressure to do the job.

WARNING! Wet brakes may have reduced
stopping ability, increasing the chance of
an accident. Test the brakes after washing.
Apply the brakes several times at slow
speeds to let friction dry out the linings.

[EWB02311]

NOTICE:

Excessive water pressure

may cause water seepage and deteriora-
tion of wheel bearings, brakes, transmis-
sion seals and electrical devices. Many
expensive repair bills have resulted from
improper high-pressure detergent applica-
tions such as those available in coin-oper-
ated car washers.

[ECB00711]

4. Once most of the dirt has been hosed off,

wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or bot-
tle brush is handy for hard-to-reach places.

5. Rinse the ATV off immediately with clean wa-

ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.

6. Dry the chain and lubricate it to prevent it from

rusting.

7. Clean the seat with a vinyl upholstery cleaner

to keep the cover pliable and glossy.

8. Automotive type wax may be applied to all

painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.

U1BS11E0.book Page 1 Monday, April 5, 2010 8:56 AM

«
...
117
118
119
120
121
...
»

Содержание Raptor YFM35RA















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Raptor YFM35RA

Бренд: Taylor-Dunn Страницы: 126

Бренд: Yamaha Страницы: 200

Бренд: Yamaha Страницы: 218

YXZ 1000R SS 2020

Бренд: Yamaha Страницы: 220

Бренд: Yamaha Страницы: 126

Бренд: Panasonic Страницы: 29

Бренд: Arrowquip Страницы: 16

Бренд: Madill Страницы: 44

Бренд: Wittke Страницы: 104

Бренд: E-Z-GO Страницы: 74

Бренд: Yamaha Страницы: 282

Бренд: Hammerhead Страницы: 24

Бренд: Dawson Страницы: 6

Бренд: Baja motorsports Страницы: 55

Бренд: Yamaha Страницы: 174

Бренд: Redman and Associates Страницы: 23

Бренд: Arctic Cat Страницы: 68

AUTOMIZER FULL EJECT

Бренд: Labrie Страницы: 257

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды