Yamaha R1 Series 2015 Скачать руководство пользователя страница 611 | Manualshive

Страница: 611 / 704

background image

ABS (Anti-lock Brake System)

8-130

WARNING

EWA16710

When maintenance or checks have been performed on components related to the ABS, be sure

to perform a final check before delivering the vehicle to the customer.

EAS30531

[A] CHECKING THE ABS WARNING LIGHT

Turn the main switch to “ON”. (Do not start the engine.)
1. The ABS warning light does not come on.

•

Only the ABS warning light fails to come on. [A-1]

•

The ABS warning light and all other indicator lights fail to come on. [A-2]

2. The ABS warning light comes on. [A-3]

EAS30532

[A-1] ONLY THE ABS WARNING LIGHT FAILS TO COME ON

1. Check for a short circuit to the ground between the green/orange terminal of the ABS ECU coupler

and green/orange terminal of the meter assembly.

•

If there is short circuit to the ground, the wire harness is defective. Replace the wire harness.

2. Disconnect the ABS ECU coupler and check that the ABS warning light comes on when the main

switch is turned to “ON”.

•

If the ABS warning light does not come on, the meter assembly circuit (including the ABS warning
light [LED]) is defective. Replace the meter assembly.

•

If the ABS warning light comes on, the ABS ECU is defective. Replace the hydraulic unit assembly.

EAS30533

[A-2] THE ABS WARNING LIGHT AND OTHER INDICATOR LIGHTS FAIL TO COME ON

1. Main switch

•

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES” on page 8-177.

•

If there is no continuity, replace the main switch/immobilizer unit.

2. Battery

•

Check the condition of the battery.
Refer to “CHECKING AND CHARGING THE BATTERY” on page 8-181.

•

If the battery is defective, clean the battery terminals and recharge it, or replace the battery.

3. Main fuse

•

Check the fuse for continuity.
Refer to “CHECKING THE FUSES” on page 8-180.

•

If the main fuse is blown, replace the fuse.

4. Circuit

•

Check the meter assembly circuit.
Refer to “CIRCUIT DIAGRAM” on page 8-119.

•

If the meter assembly circuit is open, replace the wire harness.

EAS31162

[A-3] THE ABS WARNING LIGHT COMES ON

Connect the Yamaha diagnostic tool to the Yamaha diagnostic tool coupler and execute functional di-
agnosis. (For information about how to execute functional diagnosis, refer to the operation manual that
is included with the tool.)
Check that communication with the ABS ECU is possible.

•

Only the ABS ECU fails to communicate. [A-4]

•

ABS ECU and FI ECU fail to communicate. [A-5]

•

Communication is possible with the ABS ECU. [B-1] (The ABS is displayed on the select unit screen.)

«
...
609
610
611
612
613
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Бренд: APRILIA Страницы: 9

Бренд: KTM Страницы: 38

Бренд: Artotic Страницы: 9

Firstgear 512817

Бренд: Dennis Kirk Страницы: 2

Бренд: Free Spirits Страницы: 28

SCARABEO 100 4T - 06-2001 PART6

Бренд: APRILIA Страницы: 6

Бренд: UBCO Страницы: 27

SHERCO 50 SE 2022

Бренд: SHERCO Страницы: 226

Бренд: ICON Vehicle Dynamics Страницы: 4

Sixteenth Edition

Бренд: MSF Страницы: 60

Бренд: Honeywell Страницы: 93

Бренд: Shark Страницы: 92

Бренд: Memphis Shades Страницы: 2

Бренд: Memphis Shades Страницы: 2

Бренд: Memphis Shades Страницы: 2

Бренд: GÜDE Страницы: 80

Бренд: GÜDE Страницы: 88

Бренд: Shift Power Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды