Yamaha R1 Series 2015 Скачать руководство пользователя страница 342

Страница: 342 / 704

ENGINE INSPECTION

5-1

EAS20041

ENGINE INSPECTION

EAS30249

MEASURE THE COMPRESSION PRESSURE

The following procedure applies to all of the cyl-
inders.

TIP

Insufficient compression pressure will result in a
loss of performance.

1. Measure:

•

Valve clearance
Out of specification

Adjust.

Refer to “ADJUSTING THE VALVE CLEAR-
ANCE” on page 3-5.

2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Remove:

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Fuel tank cover
Refer to “GENERAL CHASSIS (2)” on page
4-7.

•

Fuel tank
Refer to “FUEL TANK” on page 7-1.

•

Air filter case
Refer to “AIR FILTER CASE” on page 7-4.

•

Air cut-off valve
Refer to “AIR INDUCTION SYSTEM” on
page 7-19.

•

Ignition coils

•

Spark plugs
Refer to “CAMSHAFTS” on page 5-9.

NOTICE

ECA13340

Before removing the spark plugs, use com-

pressed air to blow away any dirt accumulat-

ed in the spark plug wells to prevent it from

falling into the cylinders.

4. Install:

•

Compression gauge “1”

5. Measure:

•

Compression pressure
Out of specification

Refer to steps (c) and

(d).

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Set the main switch to “ON”.
b. With the throttle wide open, crank the engine

until the reading on the compression gauge
stabilizes.

WARNING

EWA17100

To prevent sparking the plug, remove all ig-

nition coil couplers and fuel injector cou-

plers before cranking the engine.

TIP

The difference in compression pressure be-
tween cylinders should not exceed 100 kPa (1
kgf/cm², 15 psi).

c. If the compression pressure is above the

maximum specification, check the cylinder
head, valve surfaces and piston crown for
carbon deposits.
Carbon deposits

Eliminate.

d. If the compression pressure is below the min-

imum specification, pour a teaspoonful of en-
gine oil into the spark plug bore and measure
again.
Refer to the following table.

Compression gauge

90890-03081

Engine compression tester

YU-33223

Standard compression pressure

(at sea level)

1450 kPa/250 r/min (14.5

kgf/cm²/250 r/min, 206.2 psi/250

r/min)

Minimum–maximum

1260–1630 kPa/250 r/min (12.6–

16.3 kgf/cm²/250 r/min, 179.2–

231.8 psi/250 r/min)

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды