Yamaha R1 Series 2015 Скачать руководство пользователя страница 319

Страница: 319 / 704

STEERING HEAD

4-102

EAS30213

REMOVING THE LOWER BRACKET

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

2. Remove:

•

Upper ring nut

•

Rubber washer

•

Lower ring nut “1”

•

Lower bracket

WARNING

EWA13730

Securely support the lower bracket so that

there is no danger of it falling.

TIP

•

Hold the lower ring nut with steering nut
wrench, and then remove the upper ring nut
with the ring nut wrench.

•

Remove the lower ring nut with the steering nut
wrench “2”.

EAS30214

CHECKING THE STEERING HEAD

1. Wash:

•

Bearing

•

Bearing race

2. Check:

•

Bearing “1”

•

Bearing race “2”

Damage/pitting

Replace the bearings and

bearing races as a set.

3. Replace:

•

Bearing

•

Bearing race

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the bearing races from the steering

head pipe “1” with a long rod “2” and hammer.

b. Remove the bearing race “3” from the lower

bracket with a floor chisel “4” and hammer.

c. Install a new dust seal and new bearing rac-

es.

NOTICE

ECA14270

If the bearing race is not installed properly,

the steering head pipe could be damaged.

TIP

•

Always replace the bearings and bearing races
as a set.

•

Whenever the steering head is disassembled,
replace the dust seal.

Ring nut wrench

90890-01268

Spanner wrench

YU-01268

Steering nut wrench

90890-01403

Exhaust flange nut wrench

YU-A9472

Recommended cleaning solvent

Kerosene

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды