Yamaha R1 Series 2015 Скачать руководство пользователя страница 277

Страница: 277 / 704

REAR BRAKE

4-60

TIP

Always install new brake pads, brake pad insu-
lators, brake pad shims, and brake pad spring as
a set.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect a clear plastic hose “1” tightly to the

bleed screw “2”. Put the other end of the hose
into an open container.

b. Loosen the bleed screw and push the brake

caliper piston into the brake caliper with your
finger.

c. Tighten the bleed screw.

d. Install the brake pad insulators and brake pad

shims onto each brake pads.

TIP

Apply silicone grease between the brake pad in-
sulator and brake pad shim.

NOTICE

ECA14150

• Do not allow grease to contact the brake

pads.

• Remove any excess grease.

e. Install the brake pads and brake pad spring.

TIP

The longer tangs “a” of the brake pad spring
must point in the direction of the brake caliper
piston.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Lubricate:

•

Rear brake caliper bolts

NOTICE

ECA14150

• Do not allow grease to contact the brake

pads.

• Remove any excess grease.

4. Install:

•

Rear brake caliper

•

Brake pad retaining bolts

•

Screw plug

5. Check:

•

Brake fluid level
Below the minimum level mark “a”

Add the

specified brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-14.

6. Check:

•

Brake pedal operation
Soft or spongy feeling

Bleed the brake sys-

tem.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM (ABS)” on page 3-16.

EAS30186

REMOVING THE REAR BRAKE CALIPER

TIP

Before disassembling the brake caliper, drain

Brake caliper bleed screw

5 Nm (0.5 m·kgf, 3.6 ft·lbf)

Recommended lubricant

Silicone grease

Rear brake caliper bolt (front)

27 Nm (2.7 m·kgf, 20 ft·lbf)

Rear brake caliper bolt (rear)

12 Nm (1.2 m·kgf, 8.7 ft·lbf)

LOCTITE®

Rear brake pad retaining bolt

17 Nm (1.7 m·kgf, 12 ft·lbf)

Rear brake caliper screw plug

2.5 Nm (0.25 m·kgf, 1.8 ft·lbf)

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды