Yamaha R1 Series 2015 Скачать руководство пользователя страница 269

Страница: 269 / 704

FRONT BRAKE

4-52

replace the brake caliper piston dust seals

and brake caliper piston seals.

EAS30175

INSTALLING THE FRONT BRAKE CALIPERS

The following procedure applies to both of the
brake calipers.
1. Install:

•

Front brake caliper “1”
(temporarily)

•

Brake hose gaskets

•

Brake hoses “2”

•

Brake hose union bolts “3”

WARNING

EWA13531

Proper brake hose routing is essential to in-

sure safe vehicle operation.

NOTICE

ECA14170

When installing the brake hose onto the

brake caliper “1”, make sure the brake pipe

“a” touches the projection “b” on the brake

caliper.

2. Remove:

•

Front brake caliper

3. Install:

•

Brake pads

•

Brake pad spring

•

Brake pad pin

•

Brake pad clips

•

Front brake caliper

Refer to “REPLACING THE FRONT BRAKE
PADS” on page 4-49.

4. Fill:

•

Brake master cylinder reservoir
(with the specified amount of the specified
brake fluid)

WARNING

EWA13090

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to

deteriorate, causing leakage and poor

brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids

may result in a harmful chemical reaction,

leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake fluid reservoir. Water

will significantly lower the boiling point of

the brake fluid and could cause vapor lock.

NOTICE

ECA13540

Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean up

any spilt brake fluid immediately.

5. Bleed:

•

Brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM (ABS)” on page 3-16.

6. Check:

•

Brake fluid level
Below the minimum level mark “a”

Add the

specified brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-14.

Specified brake fluid

DOT 4

Front brake hose union bolt

32 Nm (3.2 m·kgf, 23 ft·lbf)

New

Front brake caliper bolt

35 Nm (3.5 m·kgf, 25 ft·lbf)

Specified brake fluid

DOT 4

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды