Yamaha R1 Series 2015 Скачать руководство пользователя страница 247

Страница: 247 / 704

FRONT WHEEL

4-30

c. If the runout is above specification, remove

the sensor rotor from the wheel, rotate it by
two or three bolt holes, and then install it.

NOTICE

ECA17200

Replace the wheel sensor rotor bolts with

new ones.

d. If the runout is still above specification, re-

place the wheel sensor rotor.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30152

ADJUSTING THE FRONT WHEEL STATIC

BALANCE

TIP

•

After replacing the tire, wheel or both, the front
wheel static balance should be adjusted.

•

Adjust the front wheel static balance with the
brake disc installed.

•

Be sure to use stick-on type balancing weights.

1. Remove:

•

Balancing weight(s)

2. Find:

•

Front wheel’s heavy spot

TIP

Place the front wheel on a suitable balancing
stand.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Spin the front wheel.
b. When the front wheel stops, put an “X

” mark

at the bottom of the wheel.

c. Turn the front wheel 90

so that the “X

” mark

is positioned as shown.

d. Release the front wheel.
e. When the wheel stops, put an “X

” mark at

the bottom of the wheel.

f. Repeat steps (c) through (e) several times

until all the marks come to rest at the same
spot.

g. The spot where all the marks come to rest is

the front wheel’s heavy spot “X”.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Adjust:

•

Front wheel static balance

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Install a balancing weight “1” onto the rim ex-

actly opposite the heavy spot “X”.

TIP

Start with the lightest weight.

Wheel sensor rotor bolt

8 Nm (0.8 m·kgf, 5.8 ft·lbf)

LOCTITE®

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды