Yamaha R1 Series 2015 Скачать руководство пользователя страница 196

Страница: 196 / 704

PERIODIC MAINTENANCE

3-22

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5. Install:

•

Upper bracket
Refer to “HANDLEBARS” on page 4-74.

EAS30646

LUBRICATING THE STEERING HEAD

1. Lubricate:

•

Upper bearing

•

Lower bearing

•

Bearing race

EAS31634

CHECKING THE STEERING DAMPER

Refer to “CHECKING THE STEERING DAMP-
ER” on page 4-103.

EAS31186

CHECKING THE CHASSIS FASTENERS

Make sure that all nuts, bolts, and screws are
properly tightened.
Refer to “CHASSIS TIGHTENING TORQUES”
on page 2-22.

EAS30804

LUBRICATING THE BRAKE LEVER

Lubricate the pivoting point and metal-to-metal
moving parts of the lever.

EAS30805

LUBRICATING THE CLUTCH LEVER

Lubricate the pivoting point and metal-to-metal
moving parts of the lever.

EAS30649

LUBRICATING THE PEDAL

Lubricate the pivoting point and metal-to-metal
moving parts of the pedal.

EAS30650

CHECKING THE SIDESTAND

1. Check:

•

Sidestand operation
Check that the sidestand moves smoothly.
Rough movement

Repair or replace.

EAS30651

LUBRICATING THE SIDESTAND

Lubricate the pivoting point, metal-to-metal mov-
ing parts and spring contact point of the sides-
tand.

EAS30652

CHECKING THE SIDESTAND SWITCH

Refer to “ELECTRICAL COMPONENTS” on
page 8-173.

EAS30653

CHECKING THE FRONT FORK

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

2. Check:

•

Inner tube
Damage/scratches

Replace.

•

Front fork leg
Oil leaks between inner tube and outer tube

Replace the oil seal.

3. Hold the vehicle upright and apply the front

brake.

4. Check:

•

Front fork operation
Push down hard on the handlebar several
times and check if the front fork rebounds
smoothly.
Rough movement

Repair.

Refer to “FRONT FORK (for YZF-R1)” on
page 4-79 or refer to “FRONT FORK (for
YZF-R1M)” on page 4-90.

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Silicone grease

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Lithium-soap-based grease

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды