Yamaha R1 Series 2015 Скачать руководство пользователя страница 191

Страница: 191 / 704

PERIODIC MAINTENANCE

3-17

d. Place the other end of the hose into a con-

tainer.

e. Slowly apply the brake several times.
f. Fully squeeze the brake lever or fully depress

the brake pedal and hold it in position.

g. Loosen the bleed screw.

TIP

Loosening the bleed screw will release the pres-
sure and cause the brake lever to contact the
throttle grip or the brake pedal to fully extend.

h. Tighten the bleed screw and then release the

brake lever or brake pedal.

i. Repeat steps (e) to (h) until all of the air bub-

bles have disappeared from the brake fluid in
the plastic hose.

j. Check the operation of the hydraulic unit.

Refer to “HYDRAULIC UNIT OPERATION
TEST” on page 4-70.

NOTICE

ECA17061

Make sure that the main switch is turned to

“OFF” before checking the operation of the

hydraulic unit.

k. After operating the ABS, repeat steps (e) to (i),

and then fill the brake fluid reservoir to the
proper level with the specified brake fluid.

l. Tighten the bleed screw to specification.

m. Fill the brake fluid reservoir to the proper level

with the specified brake fluid.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-14.

WARNING

EWA13110

After bleeding the hydraulic brake system,

check the brake operation.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS31428

CHECKING THE WHEELS

The following procedure applies to both of the
wheels.
1. Check:

•

Wheel
Damage/out-of-round

Replace.

WARNING

EWA13260

Never attempt to make any repairs to the

wheel.

TIP

After a tire or wheel has been changed or re-
placed, always balance the wheel.

EAS31429

CHECKING THE TIRES

The following procedure applies to both of the
tires.
1. Check:

•

Tire pressure
Out of specification

Regulate.

A.  Front brake master cylinder
B.  Front brake caliper (left/right)
C.  Rear brake caliper

Front brake master cylinder bleed

screw

5 Nm (0.5 m·kgf, 3.6 ft·lbf)

Brake caliper bleed screw

5 Nm (0.5 m·kgf, 3.6 ft·lbf)

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды