Yamaha R1 Series 2015 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 704

background image

FEATURES

1-5

EAS30713

YCC-T (Yamaha Chip Controlled Throttle)/YCC-I (Yamaha Chip Controlled Intake)

Mechanism characteristics

Yamaha developed the YCC-T and YCC-I system employing the most advanced electronic control
technologies. Electronic control throttle systems have been used on automobiles, but Yamaha has de-
veloped a faster, more compact system specifically for the needs of a sports motorcycle. The Yamaha-
developed system has a high-speed calculating capacity that produces computations of running con-
ditions every 1/1000th of a second.
The YCC-T system is designed to respond to the throttle action of the rider by having the ECU instan-
taneously calculate the ideal throttle valve opening and generate signals to operate the motor-driven
throttle valves and thus actively control the intake air volume.
The YCC-I system calculates the value from the engine speed and throttle opening rate, activates the
intake air funnel with the electronic control motor drive to control the intake pipe length in order to gain
the high power output in all revolution ranges from low speeds to high speeds.

Aims and advantages of using YCC-T system

•

Increased engine power
By shortening the air intake path, higher engine speed is possible

o

Increased engine power.

•

Improved driveability
Air intake volume is controlled according to the operating conditions

o

Improved throttle response to

meet engine requirement.
Driving force is controlled at the optimal level according to the transmission gear position and engine
speed

o

Improved throttle control.

•

Engine braking control
Due to the throttle control, optimal engine braking is made possible.

•

Simplified idle speed control (ISC) mechanism
The bypass mechanism and ISC actuator are eliminated

o

A simple mechanism is used to maintain

a steady idle speed.

•

Reduced weight
Compared to using a sub-throttle mechanism, weight is reduced.

2

3

4

1

1

A

1. Throttle valve
2. Throttle position sensor
3. Throttle servo motor
4. Accelerator position sensor

A. To throttle grip

«
...
12
13
14
15
16
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Бренд: KAYO MOTOR Страницы: 84

Бренд: yasuni Страницы: 11

Бренд: HYOSUNG Страницы: 199

Бренд: Ducati Страницы: 123

Stealth Air Cleaner Kit

Бренд: S&S Cycle Страницы: 4

Бренд: Ducati Страницы: 77

Бренд: Honda Страницы: 123

Бренд: DYNATEK Страницы: 5

Бренд: Smarter tools Страницы: 28

Бренд: Cagiva Страницы: 230

Бренд: hepco & becker Страницы: 3

Бренд: hepco & becker Страницы: 8

Бренд: B-PWR Страницы: 11

Бренд: Race Dynamics Страницы: 28

Бренд: Gmax Страницы: 5

Бренд: 3M Страницы: 113

Бренд: BackRest Страницы: 3

Бренд: Zero Motorcycles Страницы: 146

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды