Yamaha PM1D Manager V2 Скачать руководство пользователя страница 49

Страница: 49 / 56

Preset Effects Programs (added in V1.6)

Preset Effects Programs

(added in V1.6)

• Basic effect programs

Dynamic Effects

Effects Parameters (added in V1.6)

• MULTI BAND DYNA.

[Type: STEREO]

Title

Type

Description

Multi Band Dyna.

MULTI BAND DYNA. Multi-band dynamics processor

Parameter

Range

Description

LOW GAIN

–96.0 - +12.0 [dB]

Level of the low-frequency range

MID GAIN

–96.0 - +12.0 [dB]

Level of the mid-frequency range

HIGH GAIN

–96.0 - +12.0 [dB]

Level of the high-frequency range

PRESENCE

–10 - +10

“+” settings lower the high-frequency threshold and raise
the low-frequency threshold. “–” settings do the opposite.
With a setting of 0, the high, mid, and low-frequency
ranges are all affected alike.

CMP.THRESHOLD

–24.0 - 0.0 [dB]

Compressor threshold level

CMP.RATIO

1:1 - 20:1

Compression ratio

CMP.RELEASE

5.0ms - 42.3s (@fs=48kHz),
6.0ms - 46.0s (@fs=44.1kHz)

Compressor release time

CMP.ATACK

0 - 120 [ms]

Compressor attack time

CMP.KNEE

HARD, SOFT 1 - 5

Compressor knee

CMP.BYPASS

OFF, ON

Compressor bypass

LIM.THRESHOLD

–24.0 - 0.0 [dB]

Limiter threshold

LIM.RELEASE

5.0ms - 42.3s (@fs=48kHz),
6.0ms - 46.0s (@fs=44.1kHz)

Limiter release time

LIM.ATACK

0 - 120 [ms]

Limiter attack time

LIM.KNEE

HARD, SOFT 1 - 5

Limiter knee

LIM.BYPASS

OFF, ON

Limiter bypass

LOOKUP DELAY

0.0 - 100.0 [ms]

Lookup delay

L-M XOVER

21.2 - 8.00k [Hz]

Low/mid crossover frequency

M-H XOVER

21.2 - 8.00k [Hz]

Mid/high crossover frequency

CEILING

–6.0 - 0.0 [dB], OFF

Limiting value to prevent excessive output

BALANCE

0 - 100 [%]

WET/DRY balance

Содержание PM1D Manager V2

























































Результаты поиска

Содержание PM1D Manager V2

Отзывы:

Похожие инструкции для PM1D Manager V2

Бренды по названию

Популярные бренды

Yamaha PM1D Manager V2, Дополнительное руководство

Результаты поиска

Содержание PM1D Manager V2

Отзывы:

Похожие инструкции для PM1D Manager V2

Бренды по названию

Популярные бренды