PM1D Manager V2 for Windows Owner’s Manual
14
Remote Control functionality
If you connect PM1D Manager to a Yamaha digital mixer
(DM2000 V2, 02R96 V2, and DM1000 V2) via USB, you
will be able to use the digital mixer (subsequently
referred to as the “remote controller”) to remotely con-
trol the PM1D system.
• The digital mixers that can be used for remote control are
only the DM2000 V2, 02R96 V2, and DM1000 V2, and
each must be running system software V2. Remote con-
trol from other mixers is not possible.
• If you use a remote control device, the scene data and
setup data stored in the digital mixer (DM2000 V2,
02R96 V2, DM1000 V2) will be rewritten. Please back up
all of your digital mixer’s data to a computer or other
external media before you use the remote control func-
tions. For details on how to back up, refer to the manual
of your digital mixer.
• The PM1D system’s parameters that can be remotely con-
trolled are the HA GAIN or digital gain, ATT, EQ, GATE,
COMP, MIX SEND, FADER, ON, SURROUND, CUE/
SOLO ON, DCA, and scene parameters. For details, refer
to the remote control parameter list (
• Parameters that do not match between the remote con-
troller and the PM1D will be controlled to the value that
is closest to the parameter value that was operated. This
means that the actual value may differ from the displayed
value.
Setup procedure
1. Make a USB or serial connection between the con-
sole/engine and the PC, and a USB connection
between the remote controller and the PC.
2. In the SETUP screen of the remote controller, go to
the MIDI/HOST page and set the Studio Manager
PORT to “USB” and the ID to “1.”
3. Start up PM1D Manager, and open the Option
popup window either by clicking the OPTION but-
ton in the lower left of the function menu screen or
by choosing [Manager Option] from the [Option]
menu in the menu bar.
4. In the Option window, make the port settings
shown below, and click [OK].
Communication Port:
Select the port that you will
use to communicate with the console/engine.
Remote Control Setup:
Select the USB input port
(IN PORT) and output port (OUT PORT) used to
communicate with the remote controller. If the con-
nection with the console/engine is also a USB con-
nection, be careful that you don’t select the console/
engine port by mistake.
5. From the menu bar, choose [Option] menu
→
[Remote Control Setup] to open the REMOTE
CONTROL SETUP popup window.
6. In the REMOTE CONTROL SETUP window, select
the model name of the remote controller you’re
using in the REMOTE MACHINE field.
7. In the REMOTE CONTROL SETUP window, make
channel assignments for the remote controller and
for the PM1D (
8. In the function menu screen, click the REMOTE
ONLINE/OFFLINE button (or the RE-SYNCHRO-
NIZE button in the REMOTE CONTROL SETUP
windows) to enable Online status for communica-
tion with the remote controller.
9. In the function menu screen, click the ONLINE/
OFFLINE button to enable Online status for com-
munication with the console/engine.
This completes preparations for remote control.
10. In this state, operating the parameters on the
remote controller will also control the correspond-
ing parameters on the PM1D.
For details on the parameters supported for remote
control, refer to the remote control parameter list
(
Yamaha digital mixer
(DM2000 V2, 02R96 V2,
DM1000 V2)
PM1D Manager
Console CS1D
Engine
DSP1D/DSP1D-EX
USB
USB/RS-232C
PM1D V2 system
Click
REMOTE ONLINE/
OFFLINE button
ONLINE/
OFFLINE button
