Yamaha PJP-MC24 Скачать руководство пользователя страница 11

Страница: 11 / 92

Component Names and Functions

Front

1. LED

Indicates the product’s operating status.

• POWER:

Indicates whether or not the product is on. Lights when the PJP-MC24 is on.

• ALARM:

Indicates the status of the product.Lights when an error of high priority, such

as a firmware error or memory error, is present.

• STATUS:

Indicates the communication status of the product.

• CONFERENCE:

Indicates the conference status. Lights when a conference is in session.

LED States

Basic indicator LED lighting patterns are listed below.For more information, see “Q1: When
LEDs are off or blinking” (page 78).

On Off

POWER LED

The power is on.

The power is off or the product is not receiving power.

ALARM LED

The product is experiencing an error of high priority.

The product is not experiencing an error of high priority.

STATUS LED

There is a problem with the network.

The network is functioning normally.

CONFERENCE LED

A conference is in session. Lights if even one conference is in session.

A conference is not in session.

POWER

ALARM

STATUS

LAN

CONFERENCE

LINK/

DATA

SPEED

OUT

AUDIO

CONSOLE

PROJECTPHONE

OUT

INIT

Introduction

Содержание PJP-MC24





























































































Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды

Yamaha PJP-MC24, Инструкция по эксплуатации

Результаты поиска

Содержание PJP-MC24

Отзывы:

Похожие инструкции для PJP-MC24

Бренды по названию

Популярные бренды