Yamaha PHASER MF страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 97

background image

2-3

2-2

Robot installation conditions

Installation and connections

2

2.

Robot installation conditions

2.1 Installation environments

Be sure to install the robot in the following environments.

Items

Specifications

Allowable ambient
temperature

0 to 40°C

Allowable ambient humidity 35 to 85% RH (no condensation)

Altitude

0 to 1000 meters above sea level

Ambient environments

Avoid installing near water, cutting water, oil, dust,
metallic chips and organic solvent.
Avoid installation near corrosive gas and corrosive
materials.
Avoid installation in atmosphere containing inflammable
gas, dust or liquid.
Avoid installation near objects causing electromagnetic
interference, electrostatic discharge or radio frequency
interference.

Vibration

Do not subject to impacts or vibrations.

Working space

Allow sufficient space margin to perform jobs (teaching,
inspection, repair, etc.)

For detailed information on how to install the robot controller, refer to the separate
"YAMAHA Robot Controller User's Manual".

w

WARNING

Avoid installing the robot in locations where the ambient conditions may
exceed the allowable temperature or humidity, or in environments where
excessive moisture, corrosive gases, metallic powder or dust are generated.
Malfunctions, failures or short circuits may otherwise result.

w

WARNING

•  This robot was not designed for operation in environments where inflammable or
   explosive substances are present.
•  Do not use the robot in environments containing inflammable gas, dust or
   liquids. Explosions or fire could otherwise result.

w

WARNING

Avoid using the robot in locations subject to electromagnetic interference,
electrostatic discharge or radio frequency interference. Malfunctions may
otherwise occur.

«
...
18
19
20
21
22
...
»

Содержание PHASER MF


































































































Отзывы:

Нет отзывов

Похожие инструкции для PHASER MF

Char-Lynn H Series

Бренд: Eaton Страницы: 13

Бренд: B&S Страницы: 26

NIIGATA MG(L)26HLX

Бренд: IHI Страницы: 204

Бренд: GPX Страницы: 43

Бренд: MTD Страницы: 44

Бренд: aFe Power Страницы: 16

Бренд: Volvo Страницы: 88

MOTOR ELITE-i BOX 45 Series

Бренд: gaviota Страницы: 24

Бренд: Greyhound Страницы: 20

Бренд: Detroit Diesel Страницы: 116

Бренд: Detroit Diesel Страницы: 158

Бренд: Detroit Diesel Страницы: 172

Бренд: Detroit Diesel Страницы: 174

BEVELMASTER 204B

Бренд: TRI tool Страницы: 46

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды