Yamaha PHASER MF страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 97

background image

2-1

Carrying the robot

2

Installation and connections

1.

Carrying the robot

Always use 2 people to carry the robot unit. Each person should grip the robot unit near
one end from the lower side as shown and carry with the load well balanced. Carry with
the robot facing upward (slider side upwards).

w

WARNING

Always observe the following precautions when carrying the robot.
•  Remove any and all objects such as hands and grippers attached to the
   robot slider before moving the robot. The slider will lose balance if moved
   with objects still attached and cause injuries.
•  Keep the robot balanced and don't let it tilt while moving it. If the robot
   tilts, the slider may move under its own weight causing serious injuries
   such as crushed fingers.
•  Never attempt to hold the robot in any of the following manners.

[Never try this when moving!]

• Do not carry by holding the slider.
• Do not carry by holding the cable.
• Do not carry by holding the cable carrier.
• Do not carry by gripping the end cover.

«
...
17
18
19
20
21
...
»

Содержание PHASER MF


































































































Отзывы:

Нет отзывов

Похожие инструкции для PHASER MF

Бренд: Waukesha Страницы: 142

Бренд: EBARA Страницы: 36

SEL Plus-RC Series

Бренд: Selve Страницы: 172

Бренд: NOVAK Страницы: 2

Бренд: dunkermotoren Страницы: 32

Бренд: Vanguard Страницы: 104

Бренд: Sears Страницы: 12

Бренд: Lombardini Страницы: 12

Бренд: Lombardini Страницы: 44

Бренд: Lombardini Страницы: 54

Бренд: Quectel Страницы: 37

Бренд: YS Страницы: 2

Бренд: YAMADA Страницы: 2

Бренд: Alutech Страницы: 30

Бренд: Schmalz Страницы: 2

Бренд: O.S. engine Страницы: 38

Бренд: TOSO Страницы: 6

Бренд: MerCruiser Страницы: 150

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды