Yamaha PC412-D Скачать руководство пользователя

Страница: 79 / 101

13.4. Message list

Messages appearing in the display of the PC-D/DI series and the appropriate actions are listed below.

■

Alert Message

■

Log Message

Number

Alert

Message

Log

Message

SEVERITY

Content

Action

POWER TURNED
ON

INFORMATION

- The power turned
on, or - Software
reboot was
executed

POWER TURNED
OFF

INFORMATION

- The power turned
off, or - Software
reboot was
executed

STANDBY MODE
TO NORMAL

INFORMATION

The unit
transitioned from
standby mode to
normal operating
mode.

NORMAL MODE
TO STANDBY

INFORMATION

The unit
transitioned from
normal operating
mode to standby
mode.

Amplifier Output
Muting

AMP OUTPUT
MUTING

ERROR

The protection
function operated
to mute the amp
output.

Take action to
clear the
protection function
that was the
cause.
The cause is
indicated by
another alert that
is shown at the
same time.

Mains Voltage
Over 276[V]

MAINS OVER 276V ERROR

(at startup) The
amp cannot start
up because the
power supply
voltage exceeded
the allowable
operating voltage.

Connect a stable
power supply that
is within the power
supply
requirements.

The amp stopped
because the power
supply voltage
exceeded the
allowable
operating voltage.

13. Reference

| PC412-D PC412-DI PC406-D PC406-DI Owner’s Manual

Содержание PC412-D






































































































Результаты поиска

Содержание PC412-D

Отзывы:

Похожие инструкции для PC412-D

Бренды по названию

Популярные бренды

Yamaha PC412-D, Руководство пользователя

Результаты поиска

Содержание PC412-D

Отзывы:

Похожие инструкции для PC412-D

Бренды по названию

Популярные бренды