Yamaha PC412-D страница 29 Скачать руководство пользователя

Страница: 29 / 101

5.10. AMP SETTINGS page

This shows information for the basic amp-related settings.

①

SENS./GAIN

This shows the input sensitivity or gain specified by SENS./GAIN.

②

MODE (PC-DI series only)

This shows the MODE (Lo-z, 70V, 100V) of the speaker to be connected.

③

HPF (Hi-Z) (PC-DI series only)

If MODE (

②

) is 70V or 100V, this shows the cutoff frequency (40 Hz, 80 Hz) of the HPF (high pass filter) that is

compulsorily applied.
Use the channel select keys to select the channel that you want to operate, and then press the main knob to
access the

AMP SETTINGS screen

5.11. LOAD MONITORING page

This shows the impedance that is detected by LOAD MONITORING (Lo-z only).

①

ON/OFF

This indicates whether speaker impedance is monitored (ON) or not (OFF).

②

Impedance

This shows the measured impedance.
Use the channel select keys to select the channel that you want to operate, and then press the main knob to
access the

LOAD MONITORING screen

5. Panel operations

| PC412-D PC412-DI PC406-D PC406-DI Owner’s Manual

Содержание PC412-D






































































































Результаты поиска

Содержание PC412-D

Отзывы:

Похожие инструкции для PC412-D

Бренды по названию

Популярные бренды

Yamaha PC412-D, Руководство пользователя

Результаты поиска

Содержание PC412-D

Отзывы:

Похожие инструкции для PC412-D

Бренды по названию

Популярные бренды