SETTINGS
➤
Advanced setup
En
66
Advanced setup list
• Initializing this unit also initializes measurement results for IntelliBeam and settings stored in system memory. Perform “AUTO SETUP” from the “IntelliBeam” menu again.
Menu
Settings/Adjustable range
Description
TURN ON VOLUME
OFF (Not set) (default), 1 to 70
Set the initial volume level when the power of this unit is turned on.
When set to “OFF”, volume level is the same as when this unit is turned off.
MAX VOLUME
1 to 99, MAX (Maximum) (default)
Set the maximum volume level so that this unit will not output sound beyond the
limited volume level.
INPUT LOCK
ON (INPUT key operation is disabled)
OFF (INPUT key operation is enabled) (default)
Select whether or not to enable the INPUT key on the center unit.
PANEL LOCK
ON (Key operation on the center unit is disabled)
OFF (Key operation on the center unit is enabled) (default)
Select whether or not to enable key operations on the center unit (except the
advanced setup operations).
IR INPUT POWER
ON (Enables power-on)
OFF (Disables power-on) (default)
Select whether or not to automatically turn on this unit by pressing an input selector
key on the remote control when the unit is turned off.
AC ON STANDBY
ON (Enters standby mode) (default)
OFF (Restores the state before power was lost)
Set this unit’s power to off when the AC power is recovered after the power to this
unit was lost temporally (disconnect the AC power plug from the wall outlet, power
outage, etc.).
MEMORY PROTECT
ON (Protect is performed)
OFF (Protect is not performed) (default)
Protect the settings you have saved in the system memory.
YRB FL
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the front left channel. Refer to page 73
for details of YRB-100.
YRB FR
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the front right channel. Refer to page 73
for details of YRB-100.
YRB SL
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the surround left channel. Refer to page
73 for details of YRB-100.
YRB SR
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the surround right channel. Refer to
page 73 for details of YRB-100.
AUTO POWER STANDBY
ON (This unit turns off automatically) (default setting for U.K., Europe and Russia
models)
OFF (This unit does not turn off automatically) (default setting other than U.K.,
Europe and Russia models)
When set to “ON”, this unit turns off automatically in any of the following situations:
• Audio is coming from the selected input source. However, no operations have
been performed for 8 hours or more.
•
Bluetooth
is selected as the playback device. However, no audio has come out
from the device or no operation has been performed for 20 minutes or more.
• HDMI 1, 2, or 3 is selected as the playback device. However, the playback
device has been disconnected from the selected HDMI IN jack for 20 minutes or
more.
FW UPDATE
02.00.04 (The firmware version is displayed)
START OK? (Firmware is updated)
Confirm firmware version/update firmware.
INITIALIZE
OK (All settings are restored to their default values)
CANCEL (Settings are not restored to their default values) (default)
Reset all of the parameters of this unit to the factory presets. When the unit freezed,
the problem may solve by restoring to their default values.
Содержание NS-WSW120
Страница 83: ... 2014 Yamaha Corporation YG376A0 EN ...
