Yamaha MTN850-A 2017 Скачать руководство пользователя страница 155

Страница: 155 / 560

FRONT WHEEL

4-10

EAS31148

REMOVING THE FRONT WHEEL

NOTICE

ECA21380

Keep magnets (including magnetic pick-up

tools, magnetic screwdrivers, etc.) away

from the front wheel sensor “1”, otherwise

the wheel sensor may be damaged, resulting

in improper performance of the ABS.

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

2. Remove:

•

Brake caliper (left)

•

Brake caliper (right)

•

Front wheel sensor

NOTICE

ECA21440

• Do not apply the brake lever when remov-

ing the brake calipers.

• Be sure not to contact the sensor electrode

to any metal part when removing the front

wheel sensor from the sensor housing.

3. Elevate:

•

Front wheel

TIP

Place the vehicle on a maintenance stand so
that the front wheel is elevated.

4. Loosen:

•

Wheel axle pinch bolt

5. Remove:

•

Wheel axle

•

Front wheel

EAS31149

DISASSEMBLING THE FRONT WHEEL

NOTICE

ECA21340

• Do not drop the wheel sensor rotor or sub-

ject it to shocks.

• If any solvent gets on the wheel sensor ro-

tor, wipe it off immediately.

1. Remove:

•

Oil seals

•

Wheel bearings

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Clean the surface of the front wheel hub.
b. Remove the oil seals “1” with a flat-head

screwdriver.

TIP

To prevent damaging the wheel, place a rag “2”
between the screwdriver and the wheel surface.

c. Remove the wheel bearings “3” with a gener-

al bearing puller.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30147

CHECKING THE FRONT WHEEL

1. Check:

•

Wheel axle
Roll the wheel axle on a flat surface.
Bends



Replace.

WARNING

EWA13460

Do not attempt to straighten a bent wheel ax-

le.

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MTN850-A 2017

Отзывы:

Yamaha MTN850-A 2017, Руководство по обслуживанию, Страница: 155 / 560

Результаты поиска

Содержание MTN850-A 2017

Отзывы: