Yamaha MBK MW125 2014 Скачать руководство пользователя страница 370 | Manualshive

Страница: 370 / 380

background image

TROUBLESHOOTING

9-3

Fuel system

1. Throttle body

• Damaged or loose throttle body joint

2. Air filter

• Clogged air filter element

Chassis

1. Brake(s)

• Dragging brake

Electrical system

1. Spark plug

• Incorrect spark plug gap
• Incorrect spark plug heat range

2. Ignition system

• Faulty ECU

EAS30608

OVERCOOLING

Cooling system

1. Thermostat

• Thermostat stays open

EAS30609

POOR BRAKING PERFORMANCE

• Worn brake pad
• Worn brake disc
• Air in hydraulic brake system
• Leaking brake fluid
• Faulty brake caliper kit
• Faulty brake caliper seal
• Loose union bolt
• Damaged brake hose
• Oil or grease on the brake disc
• Oil or grease on the brake pad
• Incorrect brake fluid level

EAS30610

FAULTY FRONT FORK LEGS

Leaking oil

• Bent, damaged or rusty inner tube
• Cracked or damaged outer tube
• Improperly installed oil seal
• Damaged oil seal lip
• Incorrect oil level (high)
• Loose damper rod bolt
• Damaged damper rod bolt copper washer
• Cracked or damaged front fork cap bolt O-ring

Malfunction

• Bent or damaged inner tube
• Bent or damaged outer tube
• Damaged fork spring
• Worn or damaged outer tube bushing

• Bent or damaged damper rod
• Incorrect oil viscosity
• Incorrect oil level

EAS30611

UNSTABLE HANDLING

1. Handlebar

• Bent or improperly installed handlebar

2. Steering head components

• Improperly installed lower bracket

(improperly tightened ring nut)

• Bent steering stem
• Damaged ball bearing or bearing race

3. Front fork leg(s)

• Uneven oil levels (both front fork legs)
• Unevenly tensioned fork spring (both front

fork legs)

• Broken fork spring
• Bent or damaged inner tube
• Bent or damaged outer tube

4. Swingarm

• Worn bearing or bushing
• Bent or damaged swingarm

5. Rear shock absorber assembly(-ies)

• Faulty rear shock absorber spring
• Leaking oil

6. Tire(s)

• Uneven tire pressures (front and rear)
• Incorrect tire pressure
• Uneven tire wear

7. Wheel(s)

• Incorrect wheel balance
• Deformed cast wheel
• Damaged wheel bearing
• Bent or loose wheel axle
• Excessive wheel runout

8. Frame

• Bent frame
• Damaged steering head pipe
• Improperly installed bearing race

EAS30612

FAULTY LIGHTING OR SIGNALING SYSTEM

Headlight does not come on

• Wrong headlight bulb
• Too many electrical accessories
• Hard charging
• Incorrect connection
• Improperly grounded circuit
• Poor contacts (main switch)
• Burnt-out headlight bulb

Headlight bulb burnt out

• Wrong headlight bulb

«
...
368
369
370
371
372
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: Yamaha Страницы: 435

Easyrack 6622520 01 01

Бренд: hepco & becker Страницы: 4

Бренд: HRC Страницы: 88

Бренд: Ohlins Страницы: 4

Daytona Moto2 765 2020

Бренд: Triumph Страницы: 163

Бренд: Honda Страницы: 141

Бренд: Memphis Shades Страницы: 2

SEMIFAIRING BATWING SML TOURING

Бренд: PUIG Страницы: 3

Бренд: Honda Страницы: 93

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 114

YZF-R1P 2001-2003

Бренд: Yamaha Страницы: 439

Бренд: Livall Страницы: 20

Бренд: Bagster Страницы: 2

Бренд: Petzl Страницы: 5

RR 4T ENDURO 2014 350

Бренд: Beta Страницы: 66

Бренд: Beta Страницы: 74

Бренд: Beta Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды