Yamaha MBK MW125 2014 Скачать руководство пользователя страница 362

Страница: 362 / 380

ELECTRICAL COMPONENTS

8-65

b. Measure the crankshaft position sensor re-

sistance.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS30561

CHECKING THE LEAN ANGLE SENSOR

1. Remove:

• Lean angle sensor

(from the rear fender)

2. Check:

• Lean angle sensor output voltage

Out of specification

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the test harness-lean angle sensor

1PA (3P) “1” to the lean angle sensor and
wire harness as shown.

b. Connect the pocket tester (DC 20 V) to the

test harness-lean angle sensor 1PA (3P).

c. Turn the main switch to “ON”.
d. Turn the lean angle sensor to 50°.
e. Measure the lean angle sensor output volt-

age.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS30562

CHECKING THE STARTER MOTOR
OPERATION

1. Check:

• Starter motor operation

Does not operate

→

Perform the electric

starting system troubleshooting, starting with
step 4.
Refer to “TROUBLESHOOTING” on page
8-8.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the positive battery terminal “1” and

starter motor lead “2” with a jumper lead “3”.

WARNING

EWA13810

• A wire that is used as a jumper lead must

have at least the same capacity of the bat-
tery lead, otherwise the jumper lead may
burn.

• This check is likely to produce sparks,

therefore, make sure no flammable gas or
fluid is in the vicinity.

b. Check the starter motor operation.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

white/red “1”

• Negative tester probe

→

white/blue “2”

Lean angle sensor output voltage

Less than 50°: 0.4–1.4 V
More than 50°: 3.7–4.4 V

Test harness– lean angle sensor
1PA (3P)

90890-03237

Test harness– lean angle sensor
1PA (3P)

YU-03237

• Positive tester probe

→

yellow/green (wire harness color)

• Negative tester probe

→

black/blue (wire harness color)

50˚

Содержание MBK MW125 2014





























































































































































































































































































































































































Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды

Yamaha MBK MW125 2014, Руководство по обслуживанию

Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды