background image

SIGNALING SYSTEM

8-21

EAS30501

TROUBLESHOOTING

• Any of the following fail to light: turn signal light, brake light or indicator light.
• The horn fails to sound.
• The fuel meter fails to come on.
• The speedometer fails to operate.

TIP

• Before troubleshooting, remove the following part(s):
1. Fuse box cover
2. Center cover
3. Lower leg shield
4. Storage box
5. Upper handlebar cover
6. Rear side covers

 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

Checking the signaling system

The horn fails to sound.
 

 NG

 →

OK

 ↓

1. Check the fuses.

(Main, headlight, signaling system 
and backup)
Refer to “CHECKING THE FUS-
ES” on page 8-59.

Replace the fuse(s).

2. Check the battery.

Refer to “CHECKING AND 
CHARGING THE BATTERY” on 
page 8-60
.

• Clean the battery terminals.
• Recharge or replace the battery.

3. Check the main switch.

Refer to “CHECKING THE 
SWITCHES” on page 8-55.

Replace the main switch.

4. Check the entire signaling system 

wiring.
Refer to “CIRCUIT DIAGRAM” on 
page 8-19
.

Properly connect or replace the wire har-
ness.

Check the condition of each of the sig-
naling system circuits. Refer to 
“Checking the signaling system”.

1. Check the horn switch.

Refer to “CHECKING THE 
SWITCHES” on page 8-55.

• The horn switch is faulty.
• Replace the left handlebar switch.

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы: