Yamaha MBK MW125 2014 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 380

background image

FEATURES

1-4

EAS30682

INSTRUMENT FUNCTIONS

Multi-function meter unit

WARNING

EWA12423

Be sure to stop the vehicle before making
any setting changes to the multi-function
meter unit. Changing settings while riding
can distract the operator and increase the
risk of an accident.

The multi-function meter unit is equipped with
the following:
• a speedometer
• a fuel meter
• a clock
• an outside air temperature display
• an odometer
• two tripmeters
• a fuel reserve tripmeter
• an oil change tripmeter
• a V-belt replacement tripmeter
• an oil change indicator
• a V-belt replacement indicator

TIP

• Be sure to turn the key to “ON” before using the

“SELECT” and “RESET” buttons.

• For the UK only: To switch the speedometer

and odometer/tripmeter displays between kilo-
meters and miles, press the “SELECT” button
for at least one second.

• If the coolant temperature warning light and

engine trouble warning light remain on during
the initial display mode, have the battery
charged by a Yamaha dealer.

Speedometer

The speedometer shows the vehicle’s traveling
speed.

Fuel meter

The fuel meter indicates the amount of fuel in the
fuel tank. The display segments of the fuel meter
disappear towards “E” (Empty) as the fuel level
decreases. When the bottom segment of the fuel
meter and fuel level warning indicator “ ” start
flashing, refuel as soon as possible. When the
key is turned to “ON”, all of the display segments
of the fuel meter will appear for a few seconds,
and then the fuel meter shows the actual fuel
level.

TIP

This fuel meter is equipped with a self-diagnosis
system. If a problem is detected in an electrical
circuit, all the display segments and fuel level
warning indicator start flashing. If this occurs,
check the electrical circuit.
Refer to “SIGNALING SYSTEM” on page 8-19.

1. Clock
2. “SELECT” button

3. Fuel level warning indicator “

”

4. Fuel meter
5. Speedometer
6. “RESET” button
7. Outside air temperature display
8. Odometer/tripmeters
9. Oil change indicator “OIL CHANGE”
10. V-belt replacement indicator “V-BELT”

1

2 3 4

7

5

6

8

9

10

1. Speedometer

1. Fuel level warning indicator “

”

2. Fuel meter

1

1

2

«
...
11
12
13
14
15
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: Suzuki Страницы: 199

Бренд: R&G Страницы: 21

Бренд: TRS Страницы: 38

Бренд: R&G Страницы: 13

Бренд: DYNATEK Страницы: 12

Бренд: MINIMOTO Страницы: 20

Бренд: Gemini Страницы: 20

Elefant 650 USA

Бренд: Cagiva Страницы: 136

Бренд: Yamaha Страницы: 67

Бренд: Yamaha Страницы: 61

DragStar XVS650A

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 135

Бренд: Yamaha Страницы: 213

Бренд: Yamaha Страницы: 189

Бренд: Yamaha Страницы: 242

Бренд: Yamaha Страницы: 320

Бренд: Yamaha Страницы: 610

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды