Yamaha MBK MW125 2014 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 380

background image

FEATURES

1-2

EAS20008

FEATURES

EAS30005

OUTLINE OF THE FI SYSTEM

The main function of a fuel supply system is to provide fuel to the combustion chamber at the optimum
air-fuel ratio in accordance with the engine operating conditions and the atmospheric temperature. In
the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the combustion
chamber is created by the volume of the intake air and the fuel that is metered by the jet used in the
respective carburetor.
Despite the same volume of intake air, the fuel volume requirement varies by the engine operating con-
ditions, such as acceleration, deceleration, or operating under a heavy load. Carburetors that meter the
fuel through the use of jets have been provided with various auxiliary devices, so that an optimum air-
fuel ratio can be achieved to accommodate the constant changes in the operating conditions of the en-
gine.
As the requirements for the engine to deliver more performance and cleaner exhaust gases increase,
it becomes necessary to control the air-fuel ratio in a more precise and finely tuned manner. To accom-
modate this need, this model has adopted an electronically controlled fuel injection (FI) system, in place
of the conventional carburetor system. This system can achieve an optimum air-fuel ratio required by
the engine at all times by using a microprocessor that regulates the fuel injection volume according to
the engine operating conditions detected by various sensors.
The adoption of the FI system has resulted in a highly precise fuel supply, improved engine response,
better fuel economy, and reduced exhaust emissions.

1

15

12

11

13,14

9

6,7,8,

2,3

4

5

10

1. Engine trouble warning light
2. Lean angle sensor
3. Battery
4. Fuel pump
5. ECU (engine control unit)
6. Intake air temperature sensor
7. Intake air pressure sensor
8. Throttle position sensor
9. Crankshaft position sensor
10. Ignition coil

11. Spark plug
12. O

2

sensor

13. Coolant temperature sensor
14. Injector
15. Speed sensor

«
...
9
10
11
12
13
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: Thunderbike Страницы: 11

Monarch Pass M321

Бренд: Wolfman Страницы: 5

Advanced Million Color Mini Motorcycle Lighting Kit

Бренд: LedGlow Страницы: 3

VIKING 3250D FGS

Бренд: Lincoln Electric Страницы: 56

Бренд: GAS GAS Страницы: 150

fire PANTLINER AJ6

Бренд: ALPENHEAT Страницы: 26

Бренд: N-Com Страницы: 2

Бренд: R&G Страницы: 26

Battery Relocation Kit

Бренд: BoxerCafe Страницы: 7

690 Enduro AUS 2010

Бренд: KTM Страницы: 265

Бренд: hepco & becker Страницы: 6

Бренд: SUOMY Страницы: 26

Бренд: Shad Страницы: 12

Бренд: Thermo Soles Страницы: 13

Бренд: Shark Страницы: 24

Бренд: Aosom Страницы: 25

Бренд: Denali Страницы: 3

Prime R1-HD2-9813

Бренд: Rockford Fosgate Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды