Yamaha LS9-16 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 80

background image

LS9 Editor Owner’s Manual

14

D

Ø (Phase)

Inverts the phase of the signal after AD conversion.

E

HPF (High Pass Filter)

Switches the high pass filter on/off. You can drag the numeric value up or down to edit
the cutoff frequency.

F

INS (Insert)

Enables/disables the insert-in.

(INPUT CH 1–32 only)

G

D. OUT (Direct out)

Enables/disables the direct output.

H

EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-
mate response of the EQ. You can drag within the graph to edit the response of the EQ.
To reset the EQ to flat response, hold down the <Ctrl>(<

>) key of your computer

keyboard and click the graph (The HPF setting will remain).

I

DYN1/DYN2 (Dynamics 1/Dynamics 2)

Turns the two dynamics processors on/off.
If Gate is assigned (Dynamics 1 only), the status of the gate is shown immediately below
the button.

If something other than Gate is assigned, a GR meter is shown immediately below the
button, and the amount of gain reduction is shown while this is on.
The type for each dynamics processor can be selected in the Selected Channel window.

J

MIX SEND

The bar graphs located immediately below the button
show the send level of the signals sent from the INPUT
CH to VARI type MIX buses. You can also drag the bar
graph to left or right to set the send level. While you
drag the bar graph, the send level is shown in the
numerical display area for PAN/TO STEREO MONO
(

K

).

You can set the minimum value (–

∞

dB) by holding

down the <Ctrl>(<

>) key of your computer key-

board and clicking the bar graph, or set the nominal
value (0.00 dB) by holding down the <Ctrl>(<

>)

key and <Shift> key and clicking the bar graph.
The bar graph display will change according to the
send position (pre/post) and on/off status of the signal
sent from the INPUT CH to the MIX buses.
To switch a send on/off, click the channel number
located at the left of the bar graph.

For FIXED-type MIX buses, the bar graph is
fixed at nominal level (0 dB), and only the on/
off status is shown.

Gate status

indication

On/off status

On

On

On

Off

Open/closed
status

Closed

Open

Open

—

Remarks

Gain reduction amount
is 30 dB or more

Gain reduction
amount is 0–30 dB

Gain reduction
amount is 0 dB

—

L
M

N

P

O

Q

K

J

4

6
7
8

5

9

• Pre/on (green)

• Pre/off (green)

• Post/on (yellow)

• Post/off (yellow)

NOTE

«
...
12
13
14
15
16
...
»

Содержание LS9-16

















































































Отзывы:

Нет отзывов

Похожие инструкции для LS9-16

SmartSwitch 1800

Бренд: Cabletron Systems Страницы: 48

Бренд: ICP Страницы: 77

DEVICE-MAPPER MULTIPATH 5.2

Бренд: Red Hat Страницы: 44

CLUSTER SUITE FOR ENTERPRISE LINUX 5.2

Бренд: Red Hat Страницы: 78

Бренд: Nexo Страницы: 24

Бренд: Adobe Страницы: 8

Бренд: Lowrance Страницы: 76

MN-LGD011-XX-US

Бренд: LapLink Страницы: 166

Jetstream CPX-1000

Бренд: Paradyne Страницы: 240

Бренд: M-Audio Страницы: 23

ANTI-EXECUTABLE

Бренд: FARONICS Страницы: 2

Бренд: FARONICS Страницы: 2

ThinkCentre M51

Бренд: Lenovo Страницы: 72

Бренд: Lenovo Страницы: 104

Бренд: Lenovo Страницы: 204

Бренд: Lenovo Страницы: 104

Бренд: Lenovo Страницы: 190

Бренд: Zhone Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды