Yamaha KODIAK Ultramatic Скачать руководство пользователя страница 26

Страница: 26 / 185

4-4

EBU00052

Fuel gauge

The fuel gauge indicates the amount of fuel in
the fuel tank. When the needle reaches the
red line, refill the tank at the first opportunity.

1. Fuel gauge

2. Red line

NOTE:

If the machine runs out of fuel, move the fuel
cock lever to the “RES” position. Approxi-
mately 4.5 L (0.99 Imp gal, 1.19 US gal) of
fuel will be remaining in the tank.

EBU00053

Handlebar switches

1. Light switch “

/OFF”

2. Engine stop switch “

”

3. Start switch “

”

EBU01251

Light switch “

/OFF”

Set the switch to “

” to turn on the low

beams, the taillight and the meter lighting.
Set the switch to “

” to turn on the high

beams, the taillight and the meter lighting.
Set the switch to “OFF” to turn off all the lights.

U5VH10.book Page 4 Thursday, May 16, 2002 2:18 PM

Содержание KODIAK Ultramatic


























































































































































































Результаты поиска

Содержание KODIAK Ultramatic

Отзывы:

Похожие инструкции для KODIAK Ultramatic

Бренды по названию

Популярные бренды

Yamaha KODIAK Ultramatic, Руководство пользователя

Результаты поиска

Содержание KODIAK Ultramatic

Отзывы:

Похожие инструкции для KODIAK Ultramatic

Бренды по названию

Популярные бренды