60
En
In the advanced setup, you can set basic operations of this
unit, such as on and off of a bi-amp connection, or
initialize user settings. Perform the following steps to
change settings.
1
Set this unit to the standby mode.
2
Press
A
MAIN ZONE ON/OFF
while
pressing and holding
M
STRAIGHT
on the
front panel.
The advanced setup menu appears on the front panel
display.
3
Press
L
PROGRAM
l
/
h
repeatedly to
select the parameter you want to change.
The default setting are marked with “*.”
y
•
Set values are placed in XXX of the following parameters on an
actual display screen.
SP IMP. -XXX
Selects output impedance of this unit according to
connected speakers.
REMOTE ID -XXX
Sets a remote control ID. When using multiple
Yamaha AV receivers, you can operate them with a
single remote control by setting the receiver IDs to
the same setting.
SR PIN -XXX
Resets Parental lock cord when using SIRIUS
Satellite tuner.
BI AMP - XXX
Switches on and off of bi-amp connection of main
speakers. For bi-amp connection, see page 12.
SCENE IR -XXX
Selects whether or not to transmit the control signals
to an external component connected to the REMOTE
jacks on this unit when BD/DVD or CD SCENE
function is selected.
MON.CHK - XXXX
Adds upscaling limitation on output signals to a video
monitor connected to this unit via the HDMI OUT
jack.
INIT-XXXXXXXXX
Initializes various settings stored in this unit. You can
select an initialization method from the following.
DSP PARAM: All parameters of sound field
programs
VIDEO:
Video conversion settings (resolution/
aspect) in the setup menu and the OSD
display position
ALL:
Reset this unit to initial factory
settings
CANCEL:
Cancellation of initialization
4
Press
M
STRAIGHT
a few times to select the
value you want to change.
The value selected here becomes effective when this
unit is turned on the next time. You can change
multiple settings by repeating steps 3 and 4.
5
Press
A
MAIN ZONE ON/OFF
, turns off this
system, and press
A
MAIN ZONE ON/OFF
again.
The value set in step 3 becomes effective, and this
unit turns on. When you select initialization in step 3,
the initialization is performed.
Two IDs are provided for the remote control of this unit. If
another Yamaha amplifier is in the same room, setting a
different remote control ID to this unit prevents unwanted
operation of the other amplifier.
ID1 is set for both remote control and amplifier by default.
When you change the remote control ID, display
“Advance Setup” (see the previous section) and change the
ID for the amplifier too.
1
Press
d
CODE SET
on the remote control
using a pointed object such as the tip of a
ballpoint pen.
c
TRANSMIT
blinks twice.
2
Press
m
SETUP
on the remote control.
3
Enter the desired remote control ID code.
To switch to ID1:
Enter “5019” using
t
Numeric keys
.
To switch to ID2:
Enter “5020” using
t
Numeric keys
.
Once the remote control code is registered,
c
TRANSMIT
blinks twice.
If it fails,
c
TRANSMIT
blinks six times. Repeat
from step 1.
y
•
Initializing the remote control code (see page 59) returns it to ID1.
Advanced setup
Choices:
6
Ω
MIN/8
Ω
MIN*
Choices:
ID1*/ID2
Choices:
RESET/CANCEL
Choices:
ON/OFF*
Choices:
ON*/OFF
Choices:
YES*/SKIP
ADVANCEDSETUP
Choices:
DSP PARAM/VIDEO/ALL/CANCEL
Setting a remote control ID
Содержание HTR-6260
Страница 1: ...HTR 6260 AV Receiver OWNER S MANUAL U...
Страница 2: ......
Страница 92: ...2009 Yamaha Corporation All rights reserved Printed in China WQ95420...
