Yamaha GRIZZLY 700 FI YFM7FGPX Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 164

Yamaha GRIZZLY 700 FI YFM7FGPX Скачать руководство пользователя страница 107

8-22

8

NOTE:

If a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque as
soon as possible.

4. Install the spark plug cap.

EBU27461

Engine oil and oil filter cartridge

The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter cartridge replaced at the intervals spec-
ified in the periodic maintenance and lubrication
chart.

To check the engine oil level

1. Place the ATV on a level surface.
2. Check the engine oil level on a cold engine.

NOTE:

If the engine was started before checking the oil
level, be sure to warm up the engine sufficiently,
and then wait at least 10 minutes until the oil settles
for an accurate reading.

3. Remove panel F. (See page 8-8.)

4. Remove the dipstick, and then wipe it off with

a clean rag.

5. Insert the dipstick completely into the oil filler

hole, and then remove it again to check the oil
level.

1. Dipstick

U3B462E0.book Page 22 Tuesday, March 20, 2007 11:46 AM

«
...
105
106
107
108
109
...
»

Содержание GRIZZLY 700 FI YFM7FGPX





































































































































































Отзывы:

Нет отзывов