manualshive.com logo in svg

Yamaha Grizzly 450 YFM45FGPD, Руководство пользователя, Страница: 122 / 172

Поделиться
Скачать
Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя страница 122

8-30

8

antifreeze with distilled water only. Howev-
er, if distilled water is not available, soft
water may be used for refilling. Do not use
hard water or salt water since they are
harmful to the engine.

 [ECB00991]

13. Pour the recommended coolant into the radia-

tor until it is full.

14. Install the radiator cap, start the engine, let it

idle for several minutes, and then turn it off.

15. Remove the radiator cap to check the coolant

level in the radiator. If it is low, add sufficient
coolant until it reaches the top of the radiator,
and then install the radiator cap.

16. Start the engine, and then check for coolant

leakage.

TIP

If any leakage is found, have a Yamaha dealer
check the cooling system.

17. Install the panels and the front carrier.

EBU23646

Cleaning the air filter element 

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.

TIP

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.

Antifreeze/water mixture ratio:

1:1

Recommended antifreeze:

High-quality ethylene glycol antifreeze con-
taining corrosion inhibitors for aluminum en-
gines

Coolant quantity:

Radiator capacity (including all routes):

1.32 L (1.40 US qt, 1.16 Imp.qt)

Coolant reservoir capacity (up to the maxi-
mum level mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

U1CT62E0.book  Page 30  Friday, May 11, 2012  9:03 AM

Содержание Grizzly 450 YFM45FGPD













































































































































































Отзывы:

Нет отзывов