Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя страница 118

Страница: 118 / 172

8-26

6. Check the oil filler bolt gasket for damage, and

replace it if necessary.

7. Install the oil filler bolt and its gasket, and then

tighten the bolt to the specified torque.

8. Check the differential gear case for oil leak-

age. If oil is leaking, check for the cause.

EBU23470

Coolant

The coolant level should be checked before each
ride. In addition, the coolant must be changed at
the intervals specified in the periodic maintenance
and lubrication chart.

EBU27126

To check the coolant level

1. Place the ATV on a level surface.

TIP

The coolant level must be checked on a cold en-
gine since the level varies with engine tempera-
ture.

2. Check the coolant level in the coolant reser-

voir.

TIP

The coolant should be between the minimum and
maximum level marks.

1. Differential gear oil filler bolt

2. Gasket

3. Differential gear oil
4. Correct oil level

Recommended differential gear oil:

See page 10-1.

Tightening torque:

Differential gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

1 2

U1CT62E0.book Page 26 Friday, May 11, 2012 9:03 AM

Содержание Grizzly 450 YFM45FGPD













































































































































































Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Yamaha Grizzly 450 YFM45FGPD, Руководство пользователя, Страница: 118 / 172

Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы: