Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 134

Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя страница 98

8-21

8

4. Insert the tailpipe into the muffler and align the

bolt holes.

5. Install and tighten the bolts.

WARNING

EWB02340

Do not start the engine when cleaning the
spark arrester, otherwise it could cause injury
to the eyes, burns, carbon monoxide poison-
ing, possibly leading to death, and start a fire.
Always let the exhaust system cool prior to
touching exhaust components.

EBU23920

V-belt cooling duct check hose

If dust or water collects in the V-belt cooling duct
check hose, remove the hose and clean it.

EBU23930

V-belt case drain plug

After riding in water deep enough to allow it to en-
ter the V-belt case, remove this plug to drain the
water from the case.

NOTE:

If water drains from the V-belt case after removing
the plug, have a Yamaha dealer check the ATV as
the water may affect other engine parts.

1. Tailpipe
2. Spark arrester

1. V-belt cooling duct check hose (left front side of ATV)

U5WH63E0.book Page 21 Monday, May 8, 2006 1:25 PM

«
...
96
97
98
99
100
...
»

Содержание GRIZZLY 350 YFM35GW







































































































































Отзывы:

Нет отзывов