manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя, Страница: 97 / 134

Поделиться
Скачать
Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя страница 97

8-20

8

manifold fittings for an air-tight seal. Tighten all fit-
tings securely to avoid the possibility of unfiltered
air entering the engine.

CAUTION:

ECB00460

●

Make sure that the air filter element is prop-
erly seated in the air filter case.

●

Never operate the engine with the air filter el-
ement removed. This will allow unfiltered air
to enter the engine, causing rapid engine
wear and possible engine damage. Addition-
ally, operation without the air filter element
will affect carburetor jetting with subsequent
poor performance and possible engine over-
heating.

EBU27080

Cleaning the spark arrester 

Be sure the exhaust pipe and muffler are cool be-
fore cleaning the spark arrester.

1. Remove the bolts.

2. Remove the tailpipe by pulling it out of the

muffler.

3. Tap the tailpipe lightly, and then use a wire

brush to remove any carbon deposits from the
spark arrester portion of the tailpipe and inside
of the tailpipe housing.

1. Bolt
2. Tailpipe

U5WH63E0.book  Page 20  Monday, May 8, 2006  1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Отзывы:

Нет отзывов