Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 134

Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя страница 62

7-9

7

installed and used according to instructions.
Improper installation of accessories or modifi-
cation of this ATV may cause changes in han-
dling which in some situations could lead to an
accident. If you have questions, consult an au-
thorized ATV dealer.

Exhaust system

The exhaust system on the ATV is very hot during
and following operation. To prevent burns, avoid
touching the exhaust system. Park the ATV in a
place where pedestrians or children are not likely
to touch it. Also, avoid parking in or around dry
grass, brush or other combustible materials to pre-
vent causing a fire hazard.

WARNING

EWB01500

●

Do not touch the hot exhaust system.

●

Do not park the ATV during or after operation
in a place where others might be likely to
touch it.

●

Do not operate, idle, or park the ATV in dry
grass, dry ground cover, or combustible ma-
terials.

BE CAREFUL WHERE YOU RIDE

This ATV is designed for use on unpaved surfaces
only. Riding on paved surfaces can cause loss of
control.

WARNING

EWB01510

Always avoid paved surfaces, including side-
walks, driveways, parking lots and streets.
ATVs are designed for use on unpaved surfac-
es only. Paved surfaces may seriously affect
handling and control of the ATV, and may
cause the ATV to go out of control.

U5WH63E0.book Page 9 Monday, May 8, 2006 1:25 PM

«
...
60
61
62
63
64
...
»

Содержание GRIZZLY 350 YFM35GW







































































































































Отзывы:

Нет отзывов