Yamaha GRIZZLY 350 YFM350AZ Скачать руководство пользователя | Manualshive

Страница: 104 / 138

background image

8-25

8

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24045

Adjusting the throttle cable free play

The throttle cable free play should be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
The throttle cable free play should measure 3.0–
5.0 mm (0.12–0.20 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

TIP

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-
ble free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle cable free play, turn

the throttle cable free play adjusting bolt in di-
rection (a). To decrease the throttle cable free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U5WH66E0.book Page 25 Thursday, June 18, 2009 10:41 AM

«
...
102
103
104
105
106
...
»

Содержание GRIZZLY 350 YFM350AZ











































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRIZZLY 350 YFM350AZ

Бренд: MANCO Страницы: 5

Бренд: XY Powersports Страницы: 259

700 Diesel ATV 2007

Бренд: Arctic Cat Страницы: 184

Бренд: Can-Am Страницы: 140

Бренд: Can-Am Страницы: 144

Бренд: P.Lindberg Страницы: 107

Бренд: Troxus Страницы: 12

Бренд: U-Line Страницы: 9

Бренд: Eagle Страницы: 29

RECOIL iS CREW 2015

Бренд: Bad Boy Страницы: 60

Бренд: Yamaha Страницы: 156

Бренд: Yamaha Страницы: 374

Бренд: Cobra Страницы: 69

Бренд: Msied Страницы: 21

2009 Sportsman XP 850

Бренд: Polaris Страницы: 381

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды