background image

5-1

5

EBU19201

PRE-OPERATION CHECKS

EBU19224

Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always
follow the inspection and maintenance procedures and schedules described in the Owner’s Manual.

WARNING

EWB00481

Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equip-
ment damage. Do not operate the vehicle if you find any problem. If a problem cannot be corrected
by the procedures provided in this manual, have the vehicle inspected by a Yamaha dealer.

Before using this vehicle, check the following points:

ITEM

ROUTINE

PAGE

Fuel

• Check fuel level in fuel tank, and add recommended fuel if neces-

sary.

• Check fuel line for leakage. Correct if necessary.

4-9, 5-3

Engine oil

• Check oil level in engine, and add recommended oil to specified lev-

el if necessary.

• Check ATV for oil leakage. Correct if necessary.

5-3, 8-12

Final gear oil

• Check ATV for oil leakage. Correct if necessary.

5-3, 8-16

Front brake

• Check operation. If soft or spongy, have Yamaha dealer bleed hy-

draulic system.

• Check brake pads for wear, and replace if necessary.
• Check brake fluid level in reservoir, and add recommended brake 

fluid to specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

5-3, 8-26, 8-28, 8-29

U5WH66E0.book  Page 1  Thursday, June 18, 2009  10:41 AM

Содержание GRIZZLY 350 YFM350AZ











































































































































Отзывы: