Yamaha GRIZZLY 350 YFM350AA Скачать руководство пользователя | Manualshive

Страница: 90 / 136

background image

8-12

8

EBU23319

Engine oil and oil filter cartridge

The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter cartridge replaced at the intervals spec-
ified in the periodic maintenance and lubrication
chart.

To check the engine oil level

1. Place the ATV on a level surface.
2. Check the engine oil level on a cold engine.

TIP

If the engine was started before checking the oil
level, be sure to warm up the engine sufficiently,
and then wait at least ten minutes until the oil set-
tles for an accurate reading.

3. Remove the engine oil filler cap, and then

wipe the engine oil dipstick off with a clean
rag.

4. Insert the dipstick into the filler hole (without

screwing it in), and then remove it again to
check the oil level.

TIP

The engine oil should be between the tip of the dip-
stick and the maximum level mark.

1. Engine oil filler cap

U5WH67E0.book Page 12 Thursday, June 3, 2010 2:10 PM

«
...
88
89
90
91
92
...
»

Содержание GRIZZLY 350 YFM350AA









































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRIZZLY 350 YFM350AA

Sportsman 9921483

Бренд: Polaris Страницы: 207

Бренд: Chongqing Astronautic Bashan Motorcycle Manufacturing Страницы: 16

GROUND FORCE ELITE

Бренд: Razor Страницы: 16

outlander 400 series

Бренд: Can-Am Страницы: 156

Бренд: Cectec Страницы: 212

Haul-Master 64831

Бренд: Harbor Freight Tools Страницы: 16

Viper 40E (RXL-40E)

Бренд: E-TON Страницы: 24

SmarTrax John Deere 8770

Бренд: Raven Страницы: 48

Бренд: E-Z-GO Страницы: 114

Бренд: Hammerhead Страницы: 24

Бренд: Yamaha Страницы: 148

Бренд: Yamaha Страницы: 154

Бренд: Yamaha Страницы: 154

Бренд: Husqvarna Страницы: 33

Бренд: Husqvarna Страницы: 56

Бренд: Truxta Страницы: 24

Ninebot Gokart Kit

Бренд: Segway Страницы: 4

Бренд: Snapper Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды