Yamaha GRIZZLY 350 YFM350AA Скачать руководство пользователя | Manualshive

Страница: 103 / 136

background image

8-25

8

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24047

Adjusting the throttle lever free play

The throttle lever free play should be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.

The throttle lever free play should measure 3.0–
5.0 mm (0.12–0.20 in) as shown. Periodically
check the throttle lever free play and, if necessary,
adjust it as follows.

TIP

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle le-
ver free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle lever free play, turn

the throttle lever free play adjusting bolt in di-
rection (a). To decrease the throttle lever free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U5WH67E0.book Page 25 Thursday, June 3, 2010 2:10 PM

«
...
101
102
103
104
105
...
»

Содержание GRIZZLY 350 YFM350AA









































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRIZZLY 350 YFM350AA

Lynx 1200 4-TEC 900 ACE 2018

Бренд: BRP Страницы: 164

Бренд: Pioneer Страницы: 300

Бренд: SAF-HOLLAND Страницы: 20

Transicold X4 7300

Бренд: Carrier Страницы: 282

Бренд: Mahindra Страницы: 79

Бренд: Yerf-Dog Страницы: 25

Бренд: BAIC Страницы: 254

Бренд: Kubota Страницы: 112

Бренд: Samsung Страницы: 172

FXNytro FX10RTRSZ

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 142

Бренд: Volvo Страницы: 64

Бренд: ShoreLand'r Страницы: 17

Ditch Witch HF482

Бренд: Charles Machine Works Страницы: 6

Бренд: Charles Machine Works Страницы: 31

Ditch Witch SK5BB

Бренд: Charles Machine Works Страницы: 27

Бренд: Claas Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды