Yamaha GF12/12 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 26

background image

20

Front and rear panel

—Owner’s Manual

B

ST INSERT I/O jacks

These are TRS phone input/output jacks for
inserting external effect processors between the
ST bus and the STEREO fader. The nominal
input/output level is 0 dB. The pin wiring is
shown in the following diagram.

C

C-R OUT (control room monitor out) jacks

These are 1/4" phone output jacks (unbalanced)
for monitoring the PFL/AFL bus or the input sig-
nal from the TAPE IN jacks (

4

). The nominal

output level is +4 dB. The pin wiring is shown in
the following diagram.

D

GROUP OUT jacks 1–4

These are 1/4" phone jacks (unbalanced) which
individually output the signals of GROUP buses
1–4. The nominal output level is +4 dB.

E

POWER switch

This switch turns the power of the mixer on or
off.

1/4" phone plug

1/4" phone plug

1/4" TRS phone plug

To processor’s input

From processor’s output

Connect to INSERT I/O jack

Tip (send)

Tip (send)

Ring (return)

Sleeve (ground)

Sleeve (ground)

Tip (return)

Sleeve (ground)

1/4" phone plug

Tip (send)

Sleeve (ground)

1/4" phone plug

Tip (send)

Sleeve (ground)

«
...
18
19
20
21
22
...
»

Содержание GF12/12



























Отзывы:

Нет отзывов

Похожие инструкции для GF12/12

Бренд: NARGESA Страницы: 33

Бренд: XTA Страницы: 29

Бренд: vc999 Страницы: 59

Бренд: Qtx Страницы: 3

Бренд: Saferoad Страницы: 24

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

BOMAG BW 100 ADM-5

Бренд: Fayat Страницы: 216

Бренд: B medical systems Страницы: 28

Synthesis SDEC-3000

Бренд: JBL Страницы: 24

Бренд: Xilica Audio Design Страницы: 30

Бренд: Safavieh Страницы: 2

Бренд: Vendlet Страницы: 2

Бренд: TC Electronic Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды