Yamaha FZS10Z Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 110

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-22

7

EAU37913

Checking the brake lever free
play

There should be no free play at the
brake lever end. If there is free play,
have a Yamaha dealer inspect the
brake system.

WARNING

EWA14211

A soft or spongy feeling in the brake
lever can indicate the presence of air
in the hydraulic system. If there is air
in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the vehicle. Air in the
hydraulic system will diminish the

braking performance, which may re-
sult in loss of control and an acci-
dent.

EAU22273

Brake light switches

The brake light, which is activated by
the brake pedal and brake lever, should
come on just before braking takes ef-
fect. If necessary, adjust the rear brake
light switch as follows, but the front
brake light switch should be adjusted
by a Yamaha dealer.
Turn the rear brake light switch adjust-
ing nut while holding the rear brake light
switch in place. To make the brake light
come on earlier, turn the adjusting nut
in direction (a). To make the brake light
come on later, turn the adjusting nut in
direction (b).

1. No brake lever free play

1

1. Rear brake light switch

2. Rear brake light switch adjusting nut

U1CA10E0.book Page 22 Tuesday, November 24, 2009 1:41 PM

«
...
68
69
70
71
72
...
»

Содержание FZS10Z















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10Z

Бренд: VEB Страницы: 63

Tear-off machine

Бренд: Allstar Страницы: 4

Бренд: yasuni Страницы: 8

Бренд: Caberg Страницы: 16

Бренд: Ice Bear Страницы: 64

Бренд: RDMOTO Страницы: 3

Бренд: Gemini Страницы: 17

Бренд: hepco & becker Страницы: 3

Бренд: APRILIA Страницы: 477

Бренд: KTM Страницы: 22

Бренд: Indian Motorcycle Страницы: 122

Бренд: Yamaha Страницы: 82

Бренд: yasuni Страницы: 16

Бренд: yasuni Страницы: 18

Бренд: ICARO 2000 Страницы: 15

Бренд: Vance and hines Страницы: 9

Бренд: YITELA Страницы: 11

690 Duke CN 2017

Бренд: KTM Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды