Yamaha FZS10Z Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 110

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-17

4

EAU39333

Adjusting the front fork

WARNING

EWA14670

Always adjust the spring preload on
both fork legs equally, otherwise
poor handling and loss of stability
may result.

Each front fork leg is equipped with a
spring preload adjusting bolt, the right
front fork leg is equipped with a re-
bound damping force adjusting screw
and the left front fork leg with a com-
pression damping force adjusting
screw.

NOTICE

ECA10101

To avoid damaging the mechanism,
do not attempt to turn beyond the
maximum or minimum settings.

Spring preload

To increase the spring preload and
thereby harden the suspension, turn
the adjusting bolt on each fork leg in di-
rection (a). To decrease the spring pre-
load and thereby soften the
suspension, turn the adjusting bolt on
each fork leg in direction (b).
Align the appropriate groove on the ad-
justing mechanism with the top of the
front fork cap bolt.

1. Spring preload adjusting bolt

1. Current setting
2. Front fork cap bolt

Spring preload setting:

Minimum (soft):

8

Standard:

5.5

Maximum (hard):

0

U1CA10E0.book Page 17 Tuesday, November 24, 2009 1:41 PM

«
...
33
34
35
36
37
...
»

Содержание FZS10Z















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10Z

Бренд: Free Spirits Страницы: 32

Бренд: hepco & becker Страницы: 4

Бренд: RDMOTO Страницы: 2

Бренд: Happy Trails Страницы: 2

Бренд: RDMOTO Страницы: 3

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 23

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 87

Бренд: hepco & becker Страницы: 3

Бренд: KEDO Страницы: 3

Бренд: KTM Страницы: 7

Бренд: Touratech Страницы: 8

Бренд: Royal Enfield Страницы: 104

Бренд: RACCEWAY Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды