Yamaha FZS10A страница 76 Скачать руководство пользователя | Manualshive

Страница: 76 / 112

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-27

7

EAU23095

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

WARNING! Damage to the outer
housing of cables may result in in-
ternal rusting and cause interfer-
ence with cable movement. Replace
damaged cables as soon as possi-
ble to prevent unsafe conditions.

[EWA10711]

EAU23114

Checking and lubricating the
throttle grip and cable

The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated by a
Yamaha dealer at the intervals speci-
fied in the periodic maintenance chart.
The throttle cable is equipped with a
rubber cover. Make sure that the cover
is securely installed. Even though the
cover is installed correctly, it does not
completely protect the cable from water
entry. Therefore, use care not to pour
water directly onto the cover or cable
when washing the vehicle. If the cable
or cover becomes dirty, wipe clean with
a moist cloth.

EAU44272

Checking and lubricating the
brake and shift pedals

Brake pedal

Shift pedal

The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.

Recommended lubricant:

Yamaha Chain and Cable Lube or
engine oil

U1CA11E0.book Page 27 Thursday, September 23, 2010 11:51 AM

«
...
74
75
76
77
78
...
»

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FZS10A

Бренд: probrake Страницы: 2

Бренд: hepco & becker Страницы: 5

Бренд: KTM Страницы: 13

Бренд: LSL Страницы: 12

SCARABEO 100 4T - 06-2001 PART6

Бренд: APRILIA Страницы: 6

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 216

Бренд: Yamaha Страницы: 380

Бренд: Yamaha Страницы: 658

Бренд: Yamaha Страницы: 106

Бренд: PMI Страницы: 2

Бренд: VESPA Страницы: 25

Competition Series

Бренд: Vance and hines Страницы: 2

Бренд: Vance and hines Страницы: 5

Бренд: Vance and hines Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды