Yamaha FZS10A страница 75 Скачать руководство пользователя

Страница: 75 / 112

PERIODIC MAINTENANCE AND ADJUSTMENT

7-26

7. Make sure that the drive chain pull-

ers are in the same position, the
drive chain slack is correct, and
the drive chain moves smoothly.

EAU23025

Cleaning and lubricating the
drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

NOTICE

ECA10583

The drive chain must be lubricated
after washing the motorcycle, riding
in the rain or riding in wet areas.

1. Clean the drive chain with kero-

sene and a small soft brush.

NOTICE:

To prevent damaging

the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents.

[ECA11121]

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

NOTICE:

Do not use

engine oil or any other lubri-
cants for the drive chain, as they

may contain substances that
could damage the O-rings.

[ECA11111]

Tightening torques:

Axle nut:

150 Nm (15 m·kgf, 108 ft·lbf)

Locknut:

16 Nm (1.6 m·kgf, 12 ft·lbf)

U1CA11E0.book Page 26 Thursday, September 23, 2010 11:51 AM

Содержание FZS10A

















































































































Результаты поиска

Содержание FZS10A

Отзывы:

Похожие инструкции для FZS10A

Бренды по названию

Популярные бренды

Yamaha FZS10A, Руководство пользователя

Результаты поиска

Содержание FZS10A

Отзывы:

Похожие инструкции для FZS10A

Бренды по названию

Популярные бренды