manualshive.com logo in svg

Yamaha FZS10A, Руководство пользователя

Поделиться
Скачать
Yamaha FZS10A Скачать руководство пользователя страница 21

INSTRUMENT AND CONTROL FUNCTIONS

4-2

4

To unlock the steering

Push the key in, and then turn it to
“OFF” while still pushing it.

EAU49391

Indicator lights and warning 
lights 

EAU11030

Turn signal indicator lights “

” 

and “

” 

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

” 

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

” 

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11254

Oil level warning light “

” 

This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

1. Push.
2. Turn.

1

2

1. Left turn signal indicator light “

”

2. Right turn signal indicator light “

”

3. Neutral indicator light “

”

4. High beam indicator light “

”

5. Engine trouble warning light “

”

6. Oil level warning light “

”

7. Coolant temperature warning light “

”

U1CA11E0.book  Page 2  Thursday, September 23, 2010  11:51 AM

Содержание FZS10A

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды