Yamaha FZR 1800 Скачать руководство пользователя | Manualshive

Страница: 58 / 104

background image

Operation

53

Recharge the battery or replace it if it is not in
good condition. (See page 81 for battery re-
charging procedures.)
Also, check that the battery leads are tight-
ened securely and that there is no corrosion
on the battery terminals. Check that the
breather hose is securely connected to the
battery and that it is not pinched.

WARNING!

Fire or explosion could result if the breath-
er hose is damaged, obstructed, or not
connected properly.

[EWJ00451]

Make sure that the battery is securely held in
place.

EJU32531

Fire extinguisher

Check that there is a full fire extinguisher on
board.

The fire extinguisher holder and cover are lo-
cated in the front storage compartment.

To store the fire extinguisher, unhook the
band and remove the cover. Place the fire ex-
tinguisher in the holder, and then place the
cover over the fire extinguisher. Fasten the
cover and the fire extinguisher with the band
securely.

To check the fire extinguisher, see the instruc-
tions supplied by the fire extinguisher manu-
facturer. Always keep the fire extinguisher
secured in the holder with its cover in place.
Always carry a fire extinguisher on board. A
fire extinguisher is not standard equipment
with this watercraft. If you do not have one,
contact a Yamaha dealer or a fire extinguisher
dealer to obtain one meeting the proper spec-
ifications.

EJU32591

Throttle lever

Check the throttle lever for proper operation.
Squeeze and release the throttle lever several
times to make sure that there is no hesitation
in its travel. It should be smooth over the com-

1

Negative (–) battery terminal: Black lead

2

Positive (+) battery terminal: Red lead

3

Breather hose

1

2

3

1

Fire extinguisher holder and cover

2

Band

Fire extinguisher:

Classification:

B-1

Capacity:

2 lb or more

1

2

UF2R10E0.book Page 53 Friday, October 31, 2008 9:14 AM

«
...
56
57
58
59
60
...
»

Содержание FZR 1800









































































































Отзывы:

Нет отзывов

Похожие инструкции для FZR 1800

Бренд: Nauticstar Страницы: 82

Бренд: Walker Bay Страницы: 8

Бренд: PURSUIT Страницы: 154

Бренд: Hobie Страницы: 16

Бренд: SeaDoo Страницы: 39

Бренд: Sea-doo Страницы: 15

Бренд: Sea Ray Boats Страницы: 26

Бренд: Sea Eagle Boats Страницы: 8

Бренд: Sea Eagle Страницы: 13

Бренд: Sea Ray Страницы: 80

Бренд: Sea-doo Страницы: 202

Бренд: Sea-doo Страницы: 314

Бренд: Hobie Страницы: 40

Бренд: SEALINE Страницы: 97

Бренд: Sea-doo Страницы: 618

Бренд: X-TREME scooter Страницы: 30

Бренд: World Cat Страницы: 70

255 DUAL CONSOLE 2015

Бренд: World Cat Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды