Yamaha FZ8NB Скачать руководство пользователя | Manualshive

Страница: 54 / 108

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-10

7

Before installing a spark plug, the spark
plug gap should be measured with a
wire thickness gauge and, if necessary,
adjusted to specification.

Clean the surface of the spark plug
gasket and its mating surface, and then
wipe off any grime from the spark plug
threads.

TIP

If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.

NOTICE

ECA10840

Do not use any tools to remove or in-
stall the spark plug cap, otherwise
the ignition coil coupler may get
damaged. The spark plug cap may
be difficult to remove because the
rubber seal on the end of the cap fits
tightly. To remove the spark plug
cap, simply twist it back and forth
while pulling it out; to install it, twist
it back and forth while pushing it in.

EAU19681

Canister (for California only)

This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the fol-
lowing:

●

Check each hose connection.

●

Check each hose and canister for
cracks or damage. Replace if dam-
aged.

●

Make sure that the canister breath-
er is not blocked, and if necessary,
clean it.

1. Spark plug gap

Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)

Tightening torque:

Spark plug:

13 Nm (1.3 m·kgf, 9.4 ft·lbf)

FUEL TANK

THROTTLE BODY

CHARCOAL CANISTER

ATMOSPHERE

#4

#3

#2

#1

U39P11E0.book Page 10 Monday, August 1, 2011 5:00 PM

«
...
52
53
54
55
56
...
»

Содержание FZ8NB













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ8NB

Бренд: PACIFIC CYCLE Страницы: 112

Бренд: R&G Страницы: 15

DaVinci RSV4-APRC

Бренд: STARLANE Страницы: 2

Quantum hardcoated N30214-WK

Бренд: National Cycle Страницы: 13

Бренд: KTM Страницы: 25

WOLVERINE R MAX 2021

Бренд: Yamaha Страницы: 190

Бренд: Yamaha Страницы: 194

WOLVERINE RMAX2 2024

Бренд: Yamaha Страницы: 196

Vstar XVS650T 2004

Бренд: Yamaha Страницы: 101

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 102

Бренд: Honda Страницы: 130

2007 PAMPERA 125

Бренд: GAS GAS Страницы: 58

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 63

Бренд: Yamaha Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды